[FC] FC Shifter Brace

[Joel McGregor]

Solid mounts would fix that problem.  Mine doesn't have them yet but will someday...  Early 'vert has them.  Late 'vert is next on the list.
Joel McGregor
________________________________________
From: corvanatics-bounces at corvair.org [corvanatics-bounces at corvair.org] On Behalf Of Ben's Bus [bensbus at verizon.net]
Sent: Tuesday, October 26, 2010 3:44 PM
To: corvanatics at corvair.org
Subject: Re: [FC] FC Shifter Brace

Both of my trucks have them..a '61 RS and a '62 GB. The one on the GB
has been beefed up substantially by the guys at Corvair Ranch as it
helps considerably with clutch chatter as well.

Ben



On 10/26/2010 4:30 PM, Ken Hand wrote:
>   I have driven and seen the brackets and braces on the earlier manual FC's. What it looked like it was for is to keep the engine from moving back and forth and ultimately to keep the shifter from moving back and forth thus staying in gear. The tolerance that it was supposed to be adjusted to was something like a 1/8 inch from the xmember, if memory serves me correctly. For the most part they are not really needed if you don't have one. If you do, you may as well use it and adjust it properly. I think I remember something in the maintenance manual about the adjustment.
>
> The above said, I have driven manual FC's and had them pop out of gear on bumpy roads. When that would happen you wouldn't really want your hand near the shifter. And, if you kept your hand on the shifter it still came out of gear because your hand would dampen the shifter movements and make it come out of gear also.
>
>
>
> Ken Hand
> 248-613-8586
> www.corvairmechanic.com
>
>
>
>
> -----Original Message-----
> From: Chris&  Bill Strickland<lechevrier at earthlink.net>
> To: corvanatics at corvair.org
> Sent: Tue, Oct 26, 2010 2:26 pm
> Subject: Re: [FC] FC Shifter Brace
>
>
>
>
>
>> I have never seen this problem myself but have heard about it -- FC's
>>
>
>> popping out of gear.
>>
>
>>
>
>
> I've driven a couple of FC's with the brace (as indicated in the Clark's
>
> reference) on them, but never connected to anything, and the only place
>
> I've come across the "popping out of gear" feature is in the Clark's
>
> catalog, where they only "believe" they were used -- of course, they
>
> have the rubber bushing to connect the brace and crossmember for sale.
>
>
>
> I suspect they were the brainchild of an overly cautious engineer,
>
> worried about the function of his "mystery shifter" feature.
>
>
>
> If your brace is different than the one in Clark's, a picture would be
>
> appropriate for identification.
>
>
>
> My initial thoughts, Back When, were that they were for some sort of
>
> skid plate mounting to protect the shift and throttle linkage at the
>
> transmission, but, if they were important, why didn't the cars have them?
>
>
>
> Bill Strickland
>
> _______________________________________________
>
> Corvanatics mailing list
>
> Corvanatics at corvair.org
>
> http://www.vv.corvair.org/mailman/listinfo/corvanatics
>
> This list sponsored by the Corvair Society of America, http://www.corvair.org/
>
>
>
> _______________________________________________
> Corvanatics mailing list
> Corvanatics at corvair.org
> http://www.vv.corvair.org/mailman/listinfo/corvanatics
> This list sponsored by the Corvair Society of America, http://www.corvair.org/
>
>
>

_______________________________________________
Corvanatics mailing list
Corvanatics at corvair.org
http://www.vv.corvair.org/mailman/listinfo/corvanatics
This list sponsored by the Corvair Society of America, http://www.corvair.org/