<VV> Starting problem

Duane, Jim Jim.Duane@DigitalNet.com
Tue, 19 Oct 2004 15:03:42 -0400


Yes, that's an excellent strategy.  The switch acts exactly like the
keyswitch.  It isolates the problem to either the wiring or the starter.
The way the wires go through the solonoid cap, there could be some
internal short that re-directs battery 12V through the ignition.  If the
starter acts normally, then the wiirng and ignition switch could be
faulty.  

JED

-----Original Message-----
From: Brian E. Terry [mailto:beterry@mijes.com] 
Sent: Tuesday, October 19, 2004 2:43 PM
To: Duane, Jim; virtualvairs@corvair.org
Subject: Re: <VV> Starting problem

Jim:

It doesn't seem to be a function of temperature.  It happened once when
the engine was warm but I had run the carbs dry on gas.  It seems to be
more like the number of cranks - if the car fires right up it will be
fine.  If it has to crank more than a couple of seconds, it will go into
this non-stop condition.  A couple of additional details:

1)  If I break the battery connection, it seems to release whatever was
causing it to crank.  I reconnect the battery right away, and it does
not continue to crank unless I engage the ignition.

2)  I checked the wiring at the solonoid, and everything there is good -
no shorts, melted wire, etc.

Is it possible to isolate between starter/solonoid and the ignition
switch by using a remote starter?  That is, if I use a remote starter
and it stops cranking when I release the button, does that mean it is
the ignition switch?  Or does the remote starter not properly simulate
the action of the real ignition switch?

Thanks.

Brian
----- Original Message -----
From: "Duane, Jim" <Jim.Duane@DigitalNet.com>
To: "Brian E. Terry" <beterry@mijes.com>; <virtualvairs@corvair.org>
Sent: Tuesday, October 19, 2004 12:43 PM
Subject: RE: <VV> Starting problem


Hi Brian

Hmmm, I believe you may have a stuck solonoid.  The coil inside can
stick/fuse/not let go, causing the engine to crank continuously.  Just a
thought, but maybe when the engine is warm, the solonoid is warm and
doesn't stick...

Jim Duane
'66 180 Corsa CVT
Colonial Corvairs
CORSA



-----Original Message-----
From: virtualvairs-admin@corvair.org
[mailto:virtualvairs-admin@corvair.org] On Behalf Of Brian E. Terry
Sent: Tuesday, October 19, 2004 9:36 AM
To: virtualvairs@corvair.org
Subject: <VV> Starting problem

Hi:

My '65 Monza under normal circumstances will start and shut off
properly.  If it has been sitting for a while and their is no gas in the
carbs, then the starter motor will not disengage when I turn the key
off.  It will keep running until it overheats or I disconnect the
battery ground.  The starter and solenoid are not that old - maybe a
couple of years and 5000 miles.  Is the starter or solenoid no good or
is this a wiring problem?  I am confused, as I would think either one of
those problems would cause it to misbehave all the time.  Any thoughts
would be greatly appreciated.  Thanks in advance.

Brian

'65 Monza Conv 110/4sp
'94 Jaguar XJS
 _______________________________________________
This message was sent by the VirtualVairs mailing list, all copyrights
are the property of the writer, please attribute properly. For help,
mailto:vv-help@corvair.org This list sponsored by the Corvair Society of
America, http://www.corvair.org/ Post messages to:
VirtualVairs@corvair.org List info:
http://www.vv.corvair.org/mailman/listinfo/virtualvairs
 _______________________________________________

__________ NOD32 1.897 (20041018) Information __________

This message was checked by NOD32 antivirus system.
http://www.nod32.com