[NoVa-Corvairs] Jan 31

[RICHARD]

Bob 

I told Jeff to get me everything that I need(clutch disk pressure plate flywheel pilot 
bushing throwout bushing seals split ring gaskets) 
Does anybody have a seal puller(if we need one) if nobody has one I will buy 
one from Jeff. 
I have a heavy duty floor jack and some jack stands I will buy the cleaner 
Thanks for the help 

Richard 
----- Original Message -----

From: "Bob Marshall via Novacc-list" <novacc-list at corvair.org> 
To: bryan at skiblack.com, novacc-list at corvair.org 
Sent: Saturday, January 24, 2015 8:23:06 PM 
Subject: Re: [NoVa-Corvairs] Jan 31 

I have 2 tall jack stands, engine cart (if needed) and seal puller. I will also bring my low profile floor jack (can't have too many floor jacks) battery impact wrench. I also have gasgachinch, permatex sealant and Anti Seize. 

Someone should bring their tool box in the event we need something that Richard may not have. 

Other things that come to mind. 
Moly grease 
Shop towels 
PB Blaster 
Cans of brake kleen 
New Gear Oil. Might consider changing it unless it is fairly new. 
Oil and oil filter. 
Extra input shaft split ring. 
Cotter pins 


It might be a good idea for someone go over to Richards before the weekend to look under the car for signs of any issues that could be taken care of while the power pack is out. U joints, side axle seals heater hose condition, shifter coupling etc. 
I recall Richard said that the Corvair Ranch did a lot of work on the car so we can probably assume the flywheel is bolted and the PP is ok. 

Richard. Send of a list of what you have ordered from the Corvair Ranch just so we know what will be there on Saturday. 

I live in Reston and could go during the week but as always two sets of eyes are better than one. 

Bob 

On 01/24/15, Bryan Blackwell via Novacc-list<novacc-list at corvair.org> wrote: 
I don't believe Richard has done a Corvair clutch or pulled the engine previously. We should bring any special tools required. Let's see: 

Tall jack stands (Doug may have) 
ATV lift or comparable (I have) 
Torque wrenches (I have) 
Bellhousing alignment dowels (I have) 

Need: 

Floor jack is preferable - Richard? 
Seal puller for the input shaft seal 
Yoke puller 
Flywheel bolt sealant 

What else? 

--Bryan 

> On Jan 24, 2015, at 3:01 PM, Bob Marshall via Novacc-list < novacc-list at corvair.org > wrote: 
> 
> Hi Richard. 
> 
> Is there anything in the way of specialty tools we need to bring next Saturday to get your clutch job done? Torque wrench, axle yoke puller or seal puller? Just trying to anticipate anything we may need. 
> 
> It will be a fun day. 
> 
> Bob 
> 
> 
> On 01/24/15, RICHARD via Novacc-list< novacc-list at corvair.org > wrote: 
> 
> Hello everybody 
> 
> I just ordered all the parts I need.I am going to drive up to the 
> Corvair Ranch next Wed or Thur to pick up the parts 
> If anybody needs something from Corvair Ranch let Jeff 
> know and I will be glad to pick it up 
> 
> Looking forward to Next Sat 
> 
> Richard 
> 
> 703 987 5879 
> 
> 
> _______________________________________________ 
> Novacc-list mailing list 
> Novacc-list at corvair.org 
> http://www.vv.corvair.org/mailman/listinfo/novacc-list 
> _______________________________________________ 
> Novacc-list mailing list 
> Novacc-list at corvair.org 
> http://www.vv.corvair.org/mailman/listinfo/novacc-list 

_______________________________________________ 
Novacc-list mailing list 
Novacc-list at corvair.org 
http://www.vv.corvair.org/mailman/listinfo/novacc-list 

_______________________________________________ 
Novacc-list mailing list 
Novacc-list at corvair.org 
http://www.vv.corvair.org/mailman/listinfo/novacc-list 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.vv.corvair.org/pipermail/novacc-list/attachments/20150125/398feb54/attachment-0001.html>