<VV> VirtualVairs Digest, Vol 133, Issue 10

[Mike Callahan]

I think the trick is to know where to put the hole for the shifter if you
don't have an old one to go by.  Any tips there.

Mike

On Fri, Feb 12, 2016 at 12:00 PM, <virtualvairs-request at corvair.org> wrote:

> Send VirtualVairs mailing list submissions to
>         virtualvairs at corvair.org
>
> To subscribe or unsubscribe via the World Wide Web, visit
>         http://www.vv.corvair.org/mailman/listinfo/virtualvairs
> or, via email, send a message with subject or body 'help' to
>         virtualvairs-request at corvair.org
>
> You can reach the person managing the list at
>         virtualvairs-owner at corvair.org
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of VirtualVairs digest..."
>
>
> Please also edit to include only the topic you're responding to when
> replying to a Digest.
> This message was sent by the VirtualVairs mailing list, all copyrights are
> the property
> of the writer, please attribute properly.
> For help, mail to: vv-help at corvair.org
> Archives at http://www.vv.corvair.org/pipermail/virtualvairs/
> This list sponsored by the Corvair Society of America,
> http://www.corvair.org/
> Change your options:
> http://www.vv.corvair.org/mailman/options/virtualvairs
> http://www.vv.corvair.org/archive.htm
>
> Today's Topics:
>
>    1. Re: CARPET HOLES (N2VZD at aol.com)
>    2. Re: CARPET HOLES (Frank DuVal)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Thu, 11 Feb 2016 19:11:07 -0500
> From: N2VZD at aol.com
> To: virtualvairs at corvair.org
> Subject: Re: <VV> CARPET HOLES
> Message-ID: <22c1d6.7076368b.43ee7d1b at aol.com>
> Content-Type: text/plain; charset="US-ASCII"
>
> In the past , I have used heated up cheap hole saws to make nice clean
> round holes in the carpet.Heat it up and hit the mark quickly. The
> residue  on
> the saw picks off clean after cooling down. I used a hot wide  putty  knife
> for gas pedal slot.
> Regards, Tim Colson   from COLD, Windy  and snowy Memphis  NY.
>
> ------------------------------
>
> Message: 2
> Date: Thu, 11 Feb 2016 22:26:28 -0500
> From: Frank DuVal <corvairduval at cox.net>
> To: virtualvairs at corvair.org
> Subject: Re: <VV> CARPET HOLES
> Message-ID: <56BD50E4.4090502 at cox.net>
> Content-Type: text/plain; charset=windows-1252; format=flowed
>
> I use sharp single edge razor blades for most of my carpet cutting. I
> also use a new sharp blade in that multi named tool: Box cuter/Stanley
> 99/razor knife/etc.
>
> I did learn the "pull a thread with drill bit" trick early in life! No
> need to repeat that mistake.
>
> Frank DuVal
>
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> This message was sent by the VirtualVairs mailing list, all copyrights are
> the property
> of the writer, please attribute properly. For help, mail to:
> vv-help at corvair.org
> This list sponsored by the Corvair Society of America,
> http://www.corvair.org/
> VirtualVairs at corvair.org
> http://www.vv.corvair.org/mailman/listinfo/virtualvairs
> Change your options:
> http://www.vv.corvair.org/mailman/options/virtualvairs
>
> ------------------------------
>
> End of VirtualVairs Digest, Vol 133, Issue 10
> *********************************************
>