[SCG] Tunnel pan screws

[Larry Claypool]

doug- rich's assessment  is what i have found as well
regards
larry claypool
----- Original Message ----- 
From: "Richard W Thompson" <Richard.W.Thompson at usa.dupont.com>
To: "Barneck Doug C TIGTA <Doug.Barneck" <Doug.Barneck at tigta.treas.gov>
Cc: <scg-list at tiger.skiblack.com>; <scg-list-bounces at tiger.skiblack.com>
Sent: Wednesday, December 07, 2005 9:19 PM
Subject: Re: [SCG] Tunnel pan screws


>
>
>
>
> Doug,
>
> I believe they are hex head sheetmetal screws, clear zinc plated, no slots
> for a screwdriver in the head, but has a wide washer at the bottom of the
> head. #10 screw, 1/2". My '65 convertible, an later April '65 car, has
> these screws and was a low, 39K mile unmolested car.
>
> What does the drawing look like for attaching screws in the Assembly
> Manual? It might give a rough representation of it.
>
> Best Regards,
>
> Rich
>
>
>
>             Barneck Doug C
>             TIGTA
>             <Doug.Barneck at tig                                          To
>             ta.treas.gov>             "'scg-list at tiger.skiblack.com'"
>             Sent by:                  <scg-list at tiger.skiblack.com>
>             scg-list-bounces@                                          cc
>             tiger.skiblack.co
>             m                                                     Subject
>                                       [SCG] Tunnel pan screws
>
>             12/07/2005 07:32
>             PM
>
>
>
>
>
>
>
> I am working on a very early 66 corsa, sept 65.  What should the tunnel 
> pan
> screws look like?
> Thanks
> DougBarneck This message was sent by the SCG-list mailing list, all
> copyrights are the property
> of the writer, please attribute properly. For help,
> mailto:scg-list-help at corvair.org
> This list sponsored by the Corvair Society of America,
> http://www.corvair.org/
> Post messages to: SCG-list at tiger.skiblack.com
> Change your options: http://www.vv.corvair.org/mailman/options/scg-list
> Get further information about SCG at
> http://members.cox.net/whubbell/Stock%20Corvair%20Group/Hello%20to%20all%20new%20and%20prior%20members.htm
>
>
> This communication is for use by the intended recipient and contains
> information that may be Privileged, confidential or copyrighted under
> applicable law. If you are not the intended recipient, you are hereby
> formally notified that any use, copying or distribution of this e-mail,
> in whole or in part, is strictly prohibited. Please notify the sender by
> return e-mail and delete this e-mail from your system. Unless explicitly
> and conspicuously designated as "E-Contract Intended", this e-mail does
> not constitute a contract offer, a contract amendment, or an acceptance
> of a contract offer. This e-mail does not constitute a consent to the
> use of sender's contact information for direct marketing purposes or for
> transfers of data to third parties.
>
> Francais Deutsch Italiano  Espanol  Portugues  Japanese  Chinese  Korean
>
>           http://www.DuPont.com/corp/email_disclaimer.html
> This message was sent by the SCG-list mailing list, all copyrights are the 
> property
> of the writer, please attribute properly. For help, 
> mailto:scg-list-help at corvair.org
> This list sponsored by the Corvair Society of America, 
> http://www.corvair.org/
> Post messages to: SCG-list at tiger.skiblack.com
> Change your options: http://www.vv.corvair.org/mailman/options/scg-list
> Get further information about SCG at 
> http://members.cox.net/whubbell/Stock%20Corvair%20Group/Hello%20to%20all%20new%20and%20prior%20members.htm
>