<VV> Has anybody made a plastic rear window for a LM?

Mike Stillwell yenko117 at yahoo.com
Fri Aug 7 21:30:17 EDT 2020


David had 5 Star use the mold that Corvair Motorsports commissioned. They most likely still have it, but it takes a dozen ordered to get them to dig it out.

Mike 
YS-117

Sent from my iPhone

> On Aug 7, 2020, at 8:48 PM, Seth Emerson via VirtualVairs <virtualvairs at corvair.org> wrote:
> 
> David Clemens had a run of these made - several years ago, in Lexan. I am getting ready to install one in my race car. I am sure others have done it. Note that the racers will need a couple or restraining straps, as well as attachment points. Probably not an issue with a street car. - Seth Emerson
> 
> 
> -----Original Message-----
> From: Charles Sadek via VirtualVairs <virtualvairs at corvair.org>
> To: 'Paul Siano' <paulsiano at yahoo.com>; virtualvairs at corvair.org
> Sent: Fri, Aug 7, 2020 5:26 pm
> Subject: Re: <VV> Has anybody made a plastic rear window for a LM?
> 
> Hi Paul,
> 
> I used Lexan-polycarbonate is required for a race car. For the rear, 1/8th" (?) allowed. I used a glass back glass/rear window for my pattern and buck. Black plastic under and surrounded the glass next to the garage in the sun. This for a heat absorber. Clamped Lexan on top of  glass, kept adding clamps letting sun and heat do the softening to bend to the glass. I don't recall how long it took but a few days as I didn't want to break the glass.
> I am told one can bend Lexan with a careful application of a torch or propane if one could get a big enough (in area) flame. I have seen it done applying a torch to Plexiglas.
> I wasn't able to bend a thicker front Lexan "windshield". I had to buy that already made. 
> 
> Chuck Sadek
> 540 273 5544  
> 
> 
> -----Original Message-----
> From: VirtualVairs [mailto:virtualvairs-bounces at corvair.org] On Behalf Of Paul Siano via VirtualVairs
> Sent: Friday, August 7, 2020 8:12 PM
> To: Virtual Vairs
> Subject: <VV> Has anybody made a plastic rear window for a LM?
> 
> I have a 5 Star for a pattern.
> It would be great to hear from a person who has done it.
> Paul Siano              Lecanto, FL            (352) 249-7519
> _______________________________________________
> This message was sent by the VirtualVairs mailing list, all copyrights are the property
> of the writer, please attribute properly. For help, mailto:vv-help at corvair.org
> This list sponsored by the Corvair Society of America, http://www.corvair.org/
> Post messages to: VirtualVairs at corvair.org
> Change your options: http://www.vv.corvair.org/mailman/options/virtualvairs
> Archives: http://www.vv.corvair.org/archive.htm
> _______________________________________________
> 
> 
> -- 
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
> 
> _______________________________________________
> This message was sent by the VirtualVairs mailing list, all copyrights are the property
> of the writer, please attribute properly. For help, mailto:vv-help at corvair.org
> This list sponsored by the Corvair Society of America, http://www.corvair.org/
> Post messages to: VirtualVairs at corvair.org
> Change your options: http://www.vv.corvair.org/mailman/options/virtualvairs
> Archives: http://www.vv.corvair.org/archive.htm
> _______________________________________________
> _______________________________________________
> This message was sent by the VirtualVairs mailing list, all copyrights are the property
> of the writer, please attribute properly. For help, mailto:vv-help at corvair.org
> This list sponsored by the Corvair Society of America, http://www.corvair.org/
> Post messages to: VirtualVairs at corvair.org
> Change your options: http://www.vv.corvair.org/mailman/options/virtualvairs
> Archives: http://www.vv.corvair.org/archive.htm
> _______________________________________________



More information about the VirtualVairs mailing list